The Gemilai 3035A is a full upgrade of the Gemilai CRM3035. It keeps the E61 layout and adds new features for better control over espresso brewing:
- The vibration pump is replaced by a quieter high-end rotary pump
- A Flow Control paddle is added
- An OPV is added to control pressure (set to 9 bar by default)
- Optional plumbed-in water supply and drain
THE GEMILAI 3035A IS AN ESPRESSO MACHINE WITH THE LEGENDARY E61 GROUP

The E61 grouphead was born in 1961 and remains the standard for a high-quality espresso group to this day.
The E61 group is essentially a mechanical 3-way valve. When you pull the lever, the pump starts:
- Valve 1 lets water flow slowly from the boiler into the grouphead to soak the coffee (Pre-infusion)
- Valve 2 lets high-pressure water flow from the group into the portafilter
- Valve 3 releases any remaining pressure in the portafilter after brewing
Features of the E61 group:
- Pros: Solidly machined, holds heat well, relatively easy to repair, manually controlled. It allows pre-infusion, which reduces channeling during extraction.
- Cons: Slower to heat up than small, simple machines
THE GEMILAI 3035A IS A HEAT EXCHANGER ESPRESSO MACHINE
A heat exchanger espresso machine has a single boiler for steam or hot water. Inside the boiler, a copper heat exchange tube runs through to supply the brewing water for espresso.
When extraction starts, the pump draws cold water from the source through the heat exchanger and into the grouphead.

- The advantage of this design is that the brewing water is separate from the boiler, so you can steam milk while pulling a shot.
- The drawback of this design is that the temperature of the water through the heat exchanger is hard to control. The longer the water stays in the coil, the hotter it gets. You can flush a small stream of water before extracting to avoid overheating.
THE GEMILAI 3035A HAS A FLOW CONTROL PADDLE

You can step in manually throughout the whole extraction to find the right recipe for each coffee.
For example: Lower the flow rate (and so the pressure on the coffee) at the start. Open it fully in the middle stage, then reduce the flow again at the end to avoid extracting too much bitterness
Combined with the OPV pressure limit of 9 bar, it can make the coffee smoother!
THE GEMILAI 3035A USES A POWERFUL BUT QUIET ITALIAN ROTARY PUMP
Compared with a vibration pump, a rotary pump is quiet, builds pressure quickly and steadily, and lasts a long time. It also costs a lot more than a vibration pump, so it is usually found on professional-level machines.
Some say the pump type does not decide coffee quality. Still, given the stability, fast pressure build-up and precise pressure setting of a rotary pump, its advantage over a vibration pump is absolute. That helps you control the espresso exactly the way you want.
Rotary pumps are usually much larger than vibration pumps, so machines with rotary pumps for commercial use are fairly large as well.
Yet the 3035A is exactly the same size as the 3035. What happened?
Gemilai fitted the 3035A with the smallest rotary pump available, 100% imported from Italy: Fluid-o-tech’s – GA series

At the same power, a small rotary pump costs much more than a large one! The result is a very complete upgrade in the 3035A, inside a very compact body.
THE GEMILAI 3035A HAS AN OPV PRESSURE VALVE
Limiting the brewing pressure is very important because it keeps the pressure from rising too high during extraction. That limits the unpleasant flavours pulled out of the coffee.
9 bar is usually considered best for espresso, and the 3035A ships set to this pressure. Some people prefer to raise it to 10 bar or cap it at 8 bar. The choice is entirely yours.
The OPV is set with a screw that can be adjusted right on the rotary pump (under the machine). This adjustment affects the rotary pump output of the Gemilai 3035A.
Specifically, there is a hole near the rear left foot of the machine. A flat-head screwdriver through this hole reaches the screw head. Turn clockwise to raise the pressure and anticlockwise to lower it.
Since the machine already has a flow control paddle, there is no need to touch the OPV unless you love to tinker.
*Important: the large brass nut under the machine is not the OPV. It is the boiler drain valve, so never open it while the machine is on and under pressure*
OTHER FEATURES OF THE GEMILAI 3035A ESPRESSO MACHINE
- Large boiler of up to 2L: Fast, strong steam pressure that froths milk in about 30 seconds.
- Hot water tap: For a hot Americano, tea, or warming cups…
- Precise PID temperature control: Set the boiler temperature from 80 to 135°C. The water through the heat exchanger is usually about 30 degrees cooler than the boiler. Keep the setting within about 118-125°C
- Switchable water supply and drain: At home and far from a water source, you can use the included 1.7L water tank and let waste water collect in the drip tray (in this case watch for the F3 low water warning on the LED display). For small commercial use, you can plumb in the supply and drain and never worry about running out of water or overflowing the drip tray)
- Professional 58mm portafilter: Easy to find accessories and gear for espresso
- Walnut portafilter handle, knobs and levers: They give the machine a softer feel that suits spaces where looks matter.
- Body entirely in stainless steel: Keeps the machine shiny no matter how much time passes
TIPS FOR USING THE GEMILAI 3035A ESPRESSO MACHINE
- A trait of heat exchanger machines is that the longer the machine stays on, the hotter the coil running through the boiler gets. Before pulling a shot, flush about 40ml of water to rebalance it.
- The temperature set on the machine is for the boiler. The espresso brewing water is always 25-30°C lower depending on how heavily you use it. Set it to at least 115°C and check the output water with a thermometer.
- F3 on the LED display means the water tank needs refilling. If the machine is plumbed in, you will never see this message
- Switch the ball valve under the machine to match tank supply (F0 – turn left) or plumbed-in supply (F1 – turn right). This relates to how the machine manages line pressure.
- You can skip the machine’s Pre-infusion setting (set it to P00) and use the paddle to pre-infuse by hand. This works better than the machine’s default soak mode.
- The machine needs about 20 minutes to heat the whole E61 group, so you cannot switch it on and brew straight away.
- If you want to save time, use a smart timer plug (Xiaomi, Rang Dong…) with the machine switch left on. Set it to turn on at 6:30am and it is ready to brew at 7. Breakfast and coffee before work!
DRAWBACKS OF THE GEMILAI 3035A ESPRESSO MACHINE
- The machine is very well put together overall. Still, a few small spots where the edges are rounded feel slightly rough. Picky or OCD-prone owners may find that annoying.
- The drip tray cover is CNC-drilled, but the holes are still a bit far apart. When you flush water, quite a lot pools on the hot surface.
- The body is so glossy that it picks up a lot of fingerprints. Avoid touching the panels, and wipe them with a damp cloth and then a paper towel to remove the marks completely.
- The power switch sits too low, so it often gets splashed while brewing and is a bit hard to clean. A switch in a more open position would be easier to use, stay cleaner and make cleaning the brewing area simpler
- The two levers for the steam wand and the hot water tap feel quite stiff. The brand may have designed them this way for safety, to avoid accidental use. But they really are stiff, which takes something away from the experience.
2 TYPES OF USERS THE GEMILAI 3035A SUITS
- Home baristas who want a commercial-level experience: Fast, powerful and high quality at a moderate cost. In particular, flow control lets the 3035A brew a wide range of coffees from light to dark roasts (something a machine without Flow control cannot do).
- Small café owners: Steam milk and pull espresso at the same time to save time. Sustained output of about 40 cups per hour
SETTING UP THE GEMILAI 3035A ESPRESSO MACHINE
Press the setting button on the display in this order:
- 1st press | Pre infusion: P00-P30, a soak time of 0 to 30 seconds
- 2nd press | Boiler temperature: From 80 to 135°C
- 3rd press | Sleep mode: EC1 (30 minutes); EC2 (60 minutes); EC3 (90 minutes); EC4 (180 minutes); EC5 (sleep mode off)
- 4th press | Water supply setting: F0 for the water tank and F1 for a plumbed-in supply (related to line pressure)
COMMON ERROR MESSAGES ON THE GEMILAI 3035A DISPLAY
- F3: The water tank is empty and needs refilling
- E2: The pump has run for over 2 minutes (usually because the coffee is ground too fine and you still try to extract)
- E3: The hot water tap has run continuously for 5 minutes (usually only on plumbed-in machines)
GEMILAI 3035A ESPRESSO MACHINE SPECIFICATIONS
- Brand: Gemilai
- Mã máy: G3035A
- Dimensions (W x D x H): 286 x 443 x 395mm
- Machine weight: 25kg
- Material: Stainless steel
- Voltage/ Power: 220V/ 2100W
- Super-quiet rotary pump
- Maximum pump pressure: 15 bars
- Built-in real-time brewing pressure gauge
- Built-in timer that starts as soon as you press brew
- Built-in digital display for setting brew profiles (temperature, time)
- Water tank: 1700ml (1.7 litres), with a built-in plumbed-in connection
- Direct drain hose connection, or waste water collected in the tray
- Made in China
- 12-month warranty
THE GEMILAI 3035A SET INCLUDES
- 1 máy pha
- 1 x 58mm double-spout portafilter
- 1 x 8g basket + 1 x 18g basket
- 1 x steel tamper with wooden handle
- 1 x plastic coffee scoop
- 1 x rubber blind basket for cleaning the machine
- 1 x water supply and drain hose set
- 1 x user manual
Tiếng Việt





















Reviews
There are no reviews yet.